-
€329,00Cafè seat designed to fit the entire Triumph Twin 790/865 air-cooled range from 2001 to 2015. 25mm narrower than the [more info]
-
€169,00The "Wave Disc®" is the best example of research and development by Galfer for Triumph. Laser cutting, stainless steel, high [more info] -
€29,28Complete gasket set suitable for all the aircooled Triumph twin motors 2001-2015 Suitable for use on both the Carb and the [more info] -
€129,00black aluminium powder coated undertail with the same finish as the frame of your Triumph. The plate holder, (not to be used with [more info] -
€45,90High-quality synthetic rubber with strong 3M adhesive on the back. If you need to remove the original pads just pull them firmly [more info] -
€79,30Kit developed to increasing lenght and excursion of 30 mm. This small change will allow you to get a hold more suitable for [more info] -
€59,00Ace handlebars were designed decades ago to offer motorcycles an easy and convenient way to replicate the appearance and position [more info] -
€26,90Do you want to replace the tail light and indicators but do not want to cut the original wiring? With this kit you do not need to [more info] -
€55,95Headlight brackets in polished aluminium complete with bushings for forks, Ø 35mm, 39mm and 41mm. We suggest a ignition [more info] -
€135,42Dynojet Carburetor Jet Kit can provide you with a simple and affordable solution to all your carburetion problems. Dynojet Jet [more info] -
€19,50If you have pulled a few more horsepower out of your engine you could run into annoying clutch slips under acceleration. The fault [more info] -
€252,54Side headlamp kit for 41 mm fork legs. The kit includes: CNC aluminium alloy bracelet black anodized, Bates headlight 4 - [more info] -
€34,16Aluminum ignition relocation kit complete with hardware for fixing on the left side. It is essential in case of mounting headlight [more info] -
€15,53original Triumph rubber brake pump cover gasket -
€55,96pair of ERGONIA footrests made of forged aluminum, finely shot blasted and milled on the upper part with precision. With a length [more info] -
€329,00slim-type seat for your Triumph Bonneville, Scrambler and Thruxton until 2015 with ribbed design that leaves the seat post frame [more info] -
€24,95Do you have a Triumph Bonneville 865/T100 with original 25mm handlebars and want to fit a pair of Bar End Mirrors? These are the [more info] -
€189,00ready-to-assemble pre-drilled aluminum rear fender designed to install with various Motone rear light kit for a simple assembly, [more info] -
€48,80Fiberglass mudguard with extremely thin angular design, is mounted without modifications on the original mount -
€102,00Front fender in paintable ABS of high-quality finish with four holes for fixing to the original bracket. (Check whether the [more info] -
€108,00Pair of tubular stainless steel engine bars diameter 25 mm for good protection. Most of the bars on the market are in standard [more info] -
€89,95This handlebar riding position is with arms outstretched and more backward than the original and handling increases dramatically, [more info] -
€15,90Pair of cables that allow the direct mounting and without any modifications to the bike, of most universal indicators on the [more info] -
€59,95black anodised headlight brackets complete with bushings for forks, Ø 35mm, 39mm and 41mm. We suggest an ignition [more info] -
€395,00This kit has been used in competitions reserved for Thruxton Cup where it was found that the simple replacement of the main jets [more info] -
€129,00chain kit which includes: - 18-tooth sprocket (JT Sprokets) in hardened chrome molybdenum steel - 43-tooth sprocket (JT [more info] -
€89,06pair of 304 stainless steel luggage bars complete with screws -
€17,50Starter knob made of CNC aluminum with knurled perimeter. It simply replaces the original plastic one for carburettor and [more info]
Accessories for Triumph Bonneville motorcycles
